Siding in Woodbury, MN.
We replace and repair siding across Woodbury — full-house replacements, single-elevation repairs, and HOA-approved color matching on townhome and association property. Storm and insurance work is part of what we do, but most Woodbury siding calls we take are simply a house that is 20 to 30 years old and due.
Below is what siding actually costs here per square, how vinyl, LP SmartSide, fiber cement, and steel compare in a freeze-thaw climate, and how we handle association palette approval before a single panel is ordered.
- Typical build era
- Late 1980s – mid 2000s across most plats
- Most common existing siding
- Builder-grade vinyl; hardboard and early fiber cement on higher-end streets
- Association property
- Very common — palette approval usually required before ordering
- Permit
- City of Woodbury building permit required for siding replacement; we pull it
- Worst-first elevation
- South and west walls on the open, newer plats
- Job size
- No minimum — single-wall repairs through full replacement
What makes a Woodbury siding job different?
Woodbury's housing stock is newer than most of the metro. Large parts of the city were platted between the late 1980s and the mid 2000s, which means an enormous number of homes are now hitting the end of their first siding cycle at the same time — builder-grade thin vinyl and, on the higher-end streets, first-generation fiber cement and hardboard installed before flashing details were as well understood as they are now.
Two things follow from that. First, a lot of what looks like a siding problem in Woodbury is actually a detail problem: a missing kickout flashing where a roof meets a wall, a window head with no drip cap, or a deck ledger cut into the cladding. We open those areas before quoting, because replacing panels over a bad detail just buys you the same failure again. Second, a very large share of Woodbury property sits inside an association with a controlled exterior palette, so material and color are usually a two-party decision — you and your board.
Exposure matters too. The newer plats east of Radio Drive and out toward Bailey Road are open, with limited mature tree cover, so south and west elevations take direct sun and wind-driven rain. That is where chalking, fading, and cracked panels show up first, and it is usually the wall we recommend addressing first if you are phasing the work.
What siding actually costs in Woodbury (2026)
Siding is priced per square — one square is 100 square feet of wall. A typical Woodbury two-story with an attached three-car garage measures roughly 22 to 30 squares of wall once you subtract windows and doors and add gables. Ranges below are installed, including removal and disposal of the existing siding.
These are Midwest Building Exteriors' own current 2026 installed prices, confirmed directly by owner Christian Musta: vinyl $900–$950 per square; LP SmartSide and fiber cement $1,200–$1,300 per square depending on finish; and steel $1,300–$1,500 per square (about $13–$15 per sq. ft.), dependent on various factors. One siding square equals 100 square feet of wall.
| Wall area | Vinyl ($900–$950/sq) | LP SmartSide ($1,200–$1,300/sq) | Fiber cement ($1,200–$1,300/sq) | Steel ($1,300–$1,500/sq) |
|---|---|---|---|---|
| 14–18 squaresSmaller townhome end unit or a single-level detached home | $12,600 – $17,100 | $16,800 – $23,400 | $16,800 – $23,400 | $18,200 – $27,000 |
| 19–24 squaresTwo-story with a two-car garage — the most common Woodbury wall area | $17,100 – $22,800 | $22,800 – $31,200 | $22,800 – $31,200 | $24,700 – $36,000 |
| 25–32 squaresTwo-story with a three-car garage, or a walkout with tall rear elevation | $22,500 – $30,400 | $30,000 – $41,600 | $30,000 – $41,600 | $32,500 – $48,000 |
| 33–45 squaresLarger two-story on the executive streets, or a small association building | $29,700 – $42,750 | $39,600 – $58,500 | $39,600 – $58,500 | $42,900 – $67,500 |
- Vinyl ($900–$950/sq)
- Exterior Portfolio Market Square at .44 mil, or a comparable Royal Building Products or CertainTeed profile. Genuine value: affordable, no repainting, and it flexes rather than cracks on impact. Removal and disposal volume is what moves the number inside this range.
- LP SmartSide ($1,200–$1,300/sq)
- Engineered wood. Our default recommendation for most Woodbury homes — real nail-holding strength, a deeper profile, and forgiving behavior through freeze-thaw. Pre-finished or field-painted; finish drives where you land in the range.
- Fiber cement ($1,200–$1,300/sq)
- Installed regularly and a legitimate choice — hard, dense, non-combustible, and it holds a factory finish for a long time. It is the least forgiving of the four on installation precision, which is the whole reason we default to LP instead. Same per-square range as LP, finish-dependent.
- Steel ($1,300–$1,500/sq)
- Christian's current installed steel pricing is $1,300–$1,500 per square, roughly $13–$15 per square foot, with the exact price dependent on various factors. Steel is rigid, non-combustible, rot-resistant, and worth considering when long service life and minimal upkeep are priorities.
Line items that move a Woodbury number
- Insulated siding upgrade (offered on request)+$150 – $300 per square
- Sheathing / OSB replacement where rot is found+$85 – $160 per sheet
- Kickout and step flashing correction at roof-to-wall+$350 – $900 per location
- Window and door head drip cap / trim wrap+$45 – $120 per opening
- House wrap replacement over bare sheathing+$60 – $110 per square
- Soffit, fascia, and gutter removal and resetquoted per elevation
- Single-elevation or partial repairquoted per job — no minimum
Ranges are installed totals in 2026 dollars — removal and disposal of the existing siding, house wrap, flashing and kickout details, trim, fasteners, permit, and cleanup included. They are planning numbers, not a quote. Wall area, number of stories, trim and gable complexity, window count, sheathing repair, and color availability all move the final figure. Repairs and partial-wall work are quoted on their own; there is no job-size minimum.
Which siding material is right for a Woodbury home?
We are generalists. We install vinyl, LP SmartSide, fiber cement, and steel, and we do not hold — or claim — a single-material specialty. What follows is how the four actually behave here, including where each one is the honest answer.
| Material | Life in MN | Installed / square | Install time |
|---|---|---|---|
| Vinyl (Exterior Portfolio Market Square, .44 mil)Real value, not a compromise: no repainting, and its flex absorbs impact that would crack a rigid panel. Comparable alternatives we install are Royal Building Products and CertainTeed. Panel thickness is what separates a good vinyl job from the thin builder-grade product most Woodbury homes are wearing now. | 20–40 years | $900 – $950 | 3–5 days |
| LP SmartSide engineered woodChristian's default recommendation for most homeowners in Minnesota. Deeper profile, strong fastener hold, and it tolerates the freeze-thaw cycle and normal installation tolerance better than a cement-based board. Pre-finished or field-painted. | 30–50 years | $1,200 – $1,300 | 3–5 days |
| Fiber cementHard, dense, non-combustible, and it holds colour a long time. We install it whenever a homeowner or an association specifies it. Its performance depends more on installation precision — clearances, flashing, caulk joints — than any other material on this list. See the category research below. | 40–50+ years | $1,200 – $1,300 | 3–5 days |
| SteelA fair option if the budget and the look suit you: rigid, rot-proof, and immune to woodpeckers. Important buying note: steel is not automatically 'storm-proof' for insurance purposes. It dents and it can be damaged by hail, and a dented steel wall is still a claim conversation. | 40–50+ years | $1,300 – $1,500 | 4–5 days |
Why we default to LP SmartSide — and what the research actually says
A note on fiber cement as a material category, not a brand. Every cement-based cladding board — regardless of who makes it — is a porous, cement-matrix product. Peer-reviewed testing on fibre-cement boards found that freeze-thaw cycling measurably changes the internal structure of the board and affects how it fails under bending load (Gorzelańczyk & Schabowicz, Materials journal, 2019, retrieved 2026-09-16). That is a property of the material class, and Minnesota delivers dozens of those cycles a year.
Field research on fiber cement wall assemblies points the same direction on moisture: Building Science Corporation's multi-year Vancouver Field Exposure Facility work instrumented fiber-cement-clad walls under heavy exterior moisture load and controlled wetting, and reported assembly moisture behaviour that depends heavily on the drainage and drying detail behind the cladding (BSC Research Report RR-1306, retrieved 2026-09-16). Industry field documentation of butt-joint gapping and caulk-joint failures in fiber cement lap siding reinforces that clearance gaps, caulking, and flashing are where these installs succeed or fail (InspectAPedia field reports, retrieved 2026-09-16).
None of that makes fiber cement a bad product, and none of it is a claim about any particular manufacturer's boards. It is why we default to LP SmartSide for most Woodbury homeowners: an engineered wood system is simply more forgiving of real-world installation tolerance in a freeze-thaw climate. If you want fiber cement — or your association requires it — we install it, and we install it to the manufacturer's published clearance, fastening, flashing, and caulk-joint specifications, because with this material category those details are the warranty.
Is steel siding storm-proof?
Steel gets marketed as the storm answer, and that oversells it. Steel is rigid and non-combustible and it will not rot, but hail dents metal — that is exactly why adjusters read dents in gutters, downspouts, and fascia as storm evidence in the first place. Choose steel because you want a very long-life, very low-maintenance wall and you like the look, not because you have been told it removes you from the hail conversation.
Does your Woodbury HOA have to approve the siding color?
In most Woodbury associations, yes — and it is the step that quietly decides your timeline. Matching an approved palette is a routine, regular part of our siding work here, not a favour. We bring physical color and profile samples to the property, photograph the existing elevations in daylight, and put the proposed product, color, and trim in front of your board in the format they actually need to approve it.
Where a palette was written years ago around a product line that has since changed, we identify the closest current-production match across the manufacturers we install and present it as a documented equivalent rather than asking a board to approve something that no longer exists.
We do the same work at association scale. If you are a board member or a property manager weighing a multi-building re-clad, we will walk the whole property, phase it by elevation and building, and price it as one project — see our commercial multifamily and HOA work and commercial siding.
- On-site color and profile samples, photographed against your existing elevations
- Written product, color, and trim submittal formatted for board review
- Closest current-production equivalent identified when a palette specifies a discontinued product
- Multi-building and multi-elevation phasing for association property
- One point of contact for the board, the manager, and the individual homeowner
Siding work from our crews
Do you do siding repairs in Woodbury, or only full replacement?
Both, with no job-size minimum. A single cracked run under a window, one elevation that took wind damage, a wall opened up to correct a flashing detail — those are all normal work for us, and we quote them on their own rather than pushing you into a whole-house number you did not ask for.
The honest limit on repair is color match. Vinyl and pre-finished panels fade over 15 to 25 years of Minnesota sun, so a new panel in the original color rarely matches the wall around it exactly. When that matters visually, the usual answer is to re-clad the affected elevation rather than patch it — and we will tell you which of the two we would do on your own house before you decide.
Insulated siding is available as an upgrade on any of these materials, replacement or repair. Ask and we will price it as a line item rather than bury it in the base number.
Who else does siding work in Woodbury?
Woodbury homeowners usually collect three or four siding bids, and most of those names come from a door knock, a yard sign, or a neighbourhood Facebook post rather than from anything you can check. So here is the check, done for you, on the siding companies most often quoted alongside us in Woodbury and the east metro.
This is not a takedown list. Every company below holds an active Minnesota residential building contractor license, which is the baseline you should demand from anyone touching your walls. We publish the state record as it reads, flag what we could not confirm, and let you decide.
| Company | MN license | Status | Expires | Licensed address | BBB |
|---|---|---|---|---|---|
| Craftsman's ChoiceCraftsmans Choice Inc | BC384780 | IssuedEnforcement flag on state record | 2027-03-31 | 5680 Quam Ave NE, Ste A, St Michael, MN 55376 | Unverified — BBB's published listing could not be retrieved on 2026-09-16. Check bbb.org directly. |
| Super SidersWinslow Companies (DBA Super Siders) | BC632296 | Issued | 2028-03-31 | 10533 Karston Ave NE, Albertville, MN 55301 | Unverified — BBB's published listing could not be retrieved on 2026-09-16. Check bbb.org directly. |
| Minnesota Exteriors IncMinnesota Exteriors Inc | BC002877 | Issued | 2028-03-31 | 8600 Jefferson Hwy, Maple Grove, MN 55369 | Unverified — BBB's published listing could not be retrieved on 2026-09-16. Check bbb.org directly. |
| Twin Cities Siding & RoofingTwin Cities Siding Professionals Operating Company LLC (DBA Twin Cities Siding and Roofing) | BC752041 | Issued | 2027-03-31 | 6500 Carlson Dr, Eden Prairie, MN 55346 | Unverified — BBB's published listing could not be retrieved on 2026-09-16. Check bbb.org directly. |
| TWS RemodelingThe Window Store Inc (DBA TWS Remodeling) | BC773859 | Issued | 2028-03-31 | 9000 Science Center Dr, New Hope, MN 55428 | Unverified — BBB's published listing could not be retrieved on 2026-09-16. Check bbb.org directly. |
| Garrett ConstructionGarrett Construction Limited Liability Company | BC785223 | Issued | 2027-03-31 | 2321 Rockwood Ave, St Paul, MN 55116 | Unverified — BBB's published listing could not be retrieved on 2026-09-16. Check bbb.org directly. |
| Anchor Roofing & ExteriorsHudson Enterprises Inc (DBA Anchor Roofing and Exteriors) | BC689351 | Issued | 2028-03-31 | 101 Bridgepoint Way, Ste 140, South St Paul, MN 55075 | Unverified — BBB's published listing could not be retrieved on 2026-09-16. Check bbb.org directly. |
- Craftsman's Choice — License BC384780 was listed as Issued through March 31, 2027, at 5680 Quam Ave NE, Ste A, St Michael, MN 55376 in the Minnesota DLI residential contractor export retrieved September 16, 2026. The export's enforcement-action field is marked, but the export provides no action type, date, outcome, case number, or order text; we therefore make no claim about what occurred. DLI's enforcement materials state, ‘A Consent Order is not a finding of fact or admission of guilt.’ The export does not establish whether this flag relates to a Consent Order. Verify the current license and any enforcement information directly at dli.mn.gov.
- Super Siders — Licensed and active with no enforcement flag on the export. Long-standing license, originally issued 2008. Their own marketing claims about years in business and families served are self-reported and we have not verified them.
- Minnesota Exteriors Inc — Licensed and active with no enforcement flag, and one of the oldest license records in the export — originally issued January 1992. A separate entity, Minnesota Exteriors Commercial LLC (BC741401), holds its own active license for commercial work.
- Twin Cities Siding & Roofing — Licensed and active with no enforcement flag. Note the operating entity name differs from the trade name — worth checking that the contract you are handed names the licensed entity.
- TWS Remodeling — Licensed and active with no enforcement flag. An earlier, similarly named license (BC283598, Window Store LLC The) shows as voluntarily terminated — the current active record is the one above.
- Garrett Construction — Licensed and active with no enforcement flag; the license number published on their own site matches the state record. The license was originally issued in August 2021, which is worth weighing against marketing that cites a longer operating history.
- Anchor Roofing & Exteriors — Licensed and active with no enforcement flag. As with several on this list, the licensed entity name differs from the trade name you see on the truck.
License numbers, status, expiry, and addresses below are taken from the Minnesota Department of Labor and Industry residential contractor license export, retrieved 2026-09-16. License status and enforcement flags change — confirm current status yourself at dli.mn.gov before you sign anything with anyone, including us. BBB accreditation and rating are shown as unverified because we could not retrieve BBB's own published listings at the time of writing; we would rather label that gap than repeat a number we have not read at the source.
Woodbury siding questions
- How much does siding cost in Woodbury, MN?
- Vinyl runs $900 to $950 per square (100 square feet of wall) installed, and LP SmartSide or fiber cement runs $1,200 to $1,300 per square depending on finish. A typical Woodbury two-story with a two-car garage measures 19 to 24 squares, which puts vinyl around $17,100 to $22,800 and LP SmartSide or fiber cement around $22,800 to $31,200 installed. Steel is currently $1,300 to $1,500 per installed square—roughly $13 to $15 per square foot—dependent on various factors, according to Christian's confirmed pricing.
- How long does a siding job take on a Woodbury home?
- Three to five days for vinyl on an average single-family home, three to five days for LP SmartSide or fiber cement, and four to five days for steel. Weather, wall area, trim complexity, and any sheathing repair we find behind the old siding can extend that. Association palette approval usually adds more calendar time than the install itself.
- What siding do you recommend for Minnesota's freeze-thaw climate?
- LP SmartSide engineered wood, for most homeowners. It holds fasteners well, carries a deeper profile, and tolerates real-world installation tolerance through repeated freeze-thaw cycling better than a cement-based board does. We install vinyl, fiber cement, and steel just as readily when budget, an association palette, or personal preference points elsewhere.
- Is vinyl siding a bad choice in Minnesota?
- No. Good vinyl is genuine value — the Exterior Portfolio Market Square profile we install at .44 mil never needs repainting, and vinyl's flex absorbs impact that would crack a rigid panel. What gives vinyl a bad name is thin builder-grade product, which is exactly what a lot of 1990s Woodbury homes are wearing. Thickness and installation are the difference.
- Is steel siding hail-proof?
- No, and you should be skeptical of anyone who says it is. Steel is rigid, non-combustible, and rot-proof, but hail dents metal — dented gutters and fascia are what adjusters read as storm evidence. Steel is a strong low-maintenance choice; it is not an exemption from storm damage or from an insurance claim.
- Will my Woodbury HOA need to approve my siding color?
- Almost certainly, if your property is in an association. We handle it as a normal part of the job: on-site color and profile samples photographed against your existing elevations, and a written product, color, and trim submittal your board can act on. Where a palette names a product that is no longer made, we identify the closest current-production equivalent and document it.
- Do you repair siding, or only replace it?
- Both, with no job-size minimum and no exclusions. One damaged run, one elevation, or the whole house — we quote it as its own job. The real constraint on a repair is color match, because 15 to 25 years of sun fades any finish; when the match would look wrong we will say so and price the elevation instead.
- Do you offer insulated siding?
- Yes, as an upgrade on request rather than a default. We price it as a separate line item — roughly $150 to $300 per square on top of the base material — so you can see exactly what the added R-value costs before you decide.
- Is siding workmanship covered by a warranty?
- Yes. Our Lifetime Craftsmanship Warranty covers workmanship on the siding we install, the same as on our roofing work, in addition to the manufacturer's material warranty for whichever product you choose. The specific terms are in the written contract and warranty documents you sign for your project.
- Can you handle a storm or insurance siding claim in Woodbury?
- Yes, and it is only part of what we do — most Woodbury siding work is straight renovation or replacement. On a storm job we document the damaged elevations photographically and communicate that documentation to your own insurance adjuster. We do not act as your public adjuster on a job we are contracted to repair.
Christian Musta
Owner, Midwest Building Exteriors
Christian Musta owns Midwest Building Exteriors, a family-led exterior restoration company with offices in Richfield, Eagan, and St. Croix Falls. He has spent 10 years in the insurance restoration industry and holds a Minnesota Public Adjuster license — a credential that reflects his command of policy language, coverage, and claim ethics. Midwest Building Exteriors does not act as a public adjuster on jobs it repairs; Christian applies that insurance knowledge to how our crews document damage and communicate with the homeowner's own insurance adjuster during a project. Every city guide on this site is written and reviewed by him, using measurements, adjuster scopes, and tear-off findings from jobs his own crews completed.
- 10 years of experience in the insurance restoration industry
- Licensed Minnesota Public Adjuster — held as a credential of competency, ethics, and policy-language knowledge, not an adjusting service we provide
- Minnesota-licensed residential building contractor
- Manufacturer-certified roofing installer (Owens Corning, TAMKO, CertainTeed)
- Installs vinyl, LP SmartSide, fiber cement, and steel siding systems
Last reviewed
Flexible financing options available.
We make protecting and upgrading your home or commercial property more affordable with flexible financing programs through trusted lending partners. Get started with comfortable monthly payments — ask us about financing options during your free inspection.
- Quick pre-qualification — no impact on your credit score
- 0% intro APR & low-rate plans through vetted partners
- Residential & commercial projects of every size