Siding in Eagan, MN.
A given week for our crews might mean a split-entry near Pilot Knob still wearing its original cedar, a rambler backed onto a pond that's soaked up thirty extra years of dampness on the shady side, and a townhome board waiting on bids matched to one approved color card. Smaller storm patches and single-wall fixes fit into the gaps between those larger projects.
- Typical build era
- 1970s – 1990s splits, two-stories, and ramblers, plus later townhome development
- Most common existing siding
- Original cedar lap or early hardboard, often due for an engineered-wood conversion
- Lot character
- Wooded, rolling terrain with frequent ponds and wetlands adjacent to individual lots
- Moisture pattern
- North-facing, pond- or wetland-adjacent walls carry higher moisture load and earlier algae growth
- Association property
- Extensive townhome and association stock; palette approval commonly required
- Permit
- City of Eagan permit required before siding work starts; our office handles the pulling
- Job size
- No minimum job size, from a single damaged wall up to a full tear-off
What makes an Eagan siding job different?
Eagan largely filled in between the 1970s and 1990s, so the detached housing stock is dominated by splits, two-stories, and ramblers finished in original cedar lap, early hardboard, or a first-generation replacement job now aging out on its own. That's a contrast with newer suburbs where we're mostly stripping thin builder-grade vinyl — here the removal is usually a genuine wood-based product, and the wall underneath has had decades to develop its own quirks.
Ground contour matters more here than it does in flatter, newer suburbs. Ponds and wetlands run through nearly every neighborhood, and the rolling, tree-covered lots frequently keep one side of a house shaded all day while another faces open water or low ground. A north wall near water holds standing moisture and green-black algae far longer than a sun-exposed elevation across town, and that speeds up wear on whatever's covering it.
Mixed elevations are common too, a layout builders leaned on throughout those decades: brick or stone up front, siding wrapping the sides and back. We work out the transition trim and a clean line at the brick edge before material ever gets ordered, not on install day.
What siding actually costs in Eagan (2026)
Pricing below is per square, and one square is defined as 100 finished square feet of exterior wall, and the cost of tearing off and hauling away whatever comes down is already built into every number. Eagan's mix of compact ramblers, townhome units, and larger executive two-stories means the size tiers here run wider than in a suburb built during a single era.
These are Midwest Building Exteriors' own current 2026 installed prices, confirmed directly by owner Christian Musta: vinyl $900–$950 per square; LP SmartSide and fiber cement $1,200–$1,300 per square depending on finish; and steel $1,300–$1,500 per square (about $13–$15 per sq. ft.), dependent on various factors. One siding square equals 100 square feet of wall.
| Wall area | Vinyl ($900–$950/sq) | LP SmartSide ($1,200–$1,300/sq) | Fiber cement ($1,200–$1,300/sq) | Steel ($1,300–$1,500/sq) |
|---|---|---|---|---|
| 12–16 squaresTownhome end unit or a compact rambler | $10,800 – $15,200 | $14,400 – $20,800 | $14,400 – $20,800 | $15,600 – $24,000 |
| 17–22 squaresA common split-entry or two-story footprint, garage included | $15,300 – $20,900 | $20,400 – $28,600 | $20,400 – $28,600 | $22,100 – $33,000 |
| 23–29 squaresLarger two-story, or a walkout rambler with a tall rear wall facing a pond or wetland | $20,700 – $27,550 | $27,600 – $37,700 | $27,600 – $37,700 | $29,900 – $43,500 |
| 30–40 squaresExecutive two-story on a larger wooded lot, or a small association building | $27,000 – $38,000 | $36,000 – $52,000 | $36,000 – $52,000 | $39,000 – $60,000 |
- Vinyl ($900–$950/sq)
- We generally reach for Exterior Portfolio's Market Square panel at .44 mil, though Royal Building Products and CertainTeed also make similar lines. It suits a rambler or townhome unit that needs a maintenance-light wall — no repainting, and enough give to flex under impact instead of cracking.
- LP SmartSide ($1,200–$1,300/sq)
- This engineered-wood product is usually what we suggest first when cedar or hardboard is coming off. It grips fasteners securely, and its extra thickness compared to vinyl means it takes Minnesota winters in stride, holding up better than a cement-based panel under the same freeze-thaw stress. Sold either pre-finished or ready for field paint.
- Fiber cement ($1,200–$1,300/sq)
- Dense and non-combustible; we put it on association jobs regularly when the specification calls for it by name. Of everything we install, it's the most sensitive to installation technique, which the research notes further down explain. Priced the same per square as LP.
- Steel ($1,300–$1,500/sq)
- Christian's real installed rate for steel is presently $1,300–$1,500 per square, approximately $13–$15 per square foot, and varies according to job factors. Its rigidity, fire resistance, and resistance to woodpecker damage can be useful on Eagan's tree-covered lots.
Line items that move a Eagan number
- Insulated siding upgrade (offered on request)+$150 – $300 per square
- Sheathing / OSB swap-out wherever we find rot+$85 – $160 per sheet
- Kickout and step-flashing fix at roof-to-wall joints+$350 – $900 per location
- Drip cap or trim wrap at window and door heads+$45 – $120 per opening
- New house wrap over exposed sheathing+$60 – $110 per square
- Brick-to-siding transition trim and flashingquoted per elevation
- Single-elevation or partial repairquoted per job — no minimum
Ranges are installed totals in 2026 dollars — removal and disposal of the existing siding, house wrap, flashing and kickout details, trim, fasteners, permit, and cleanup included. They are planning numbers, not a quote. Wall area, number of stories, trim and gable complexity, window count, sheathing repair, and color availability all move the final figure. Repairs and partial-wall work are quoted on their own; there is no job-size minimum.
Which siding material is right for an Eagan home?
We aren't tied to one house-brand product, so here's a straightforward look at how our four main options — vinyl, LP SmartSide, fiber cement, and steel — each perform on the type of wall we run into most often around Eagan.
| Material | Life in MN | Installed / square | Install time |
|---|---|---|---|
| Vinyl (Exterior Portfolio Market Square, .44 mil)A sensible swap when original cedar or a played-out first-generation vinyl job is coming down. No painting needed, and its flex absorbs a falling branch better than a rigid panel would on a wooded lot. Royal Building Products and CertainTeed offer comparable versions we also stock. | 20–40 years | $900 – $950 | 3–5 days |
| LP SmartSide engineered woodWhat we most often suggest for someone moving off cedar or hardboard who still wants a wood-grain look. Fasteners hold securely, thickness beats vinyl, and it tolerates winter temperature cycling and normal install variation better than a cement-based panel does. Comes pre-finished or ready for field paint. | 30–50 years | $1,200 – $1,300 | 3–5 days |
| Fiber cementHard, dense, non-combustible, and finished at the factory in a way that lasts, which is exactly why owners and associations sometimes name it specifically. How well it holds up depends more on clearance gaps, flashing, and caulk joints here than with anything else we carry — worth knowing on shaded, pond-adjacent walls. The research summary below goes into why. | 40–50+ years | $1,200 – $1,300 | 3–5 days |
| SteelRot-resistant and rigid, and it doesn't attract woodpeckers, a genuine advantage on Eagan's tree-heavy lots. That said, it isn't hail-proof — an impact still leaves a mark, and a dented steel wall triggers the same insurance conversation as any other material would. | 40–50+ years | $1,300 – $1,500 | 4–5 days |
Why we default to LP SmartSide — and what the research actually says
This is a category-wide issue with fiber cement, not something specific to one manufacturer. Every cement-based board is built on a porous cement matrix, and testing published in a peer-reviewed materials journal found that going through repeated freeze-thaw cycles measurably changes both the internal structure of that matrix and how the board flexes under load (Gorzelańczyk & Schabowicz, Materials journal, 2019, retrieved 2026-09-16). Minnesota supplies plenty of that cycling every winter, which matters most on Eagan's shaded, pond-adjacent walls that hold moisture far longer than a sun-facing one.
Separate moisture research reaches the same place. A multi-year outdoor exposure study Building Science Corporation ran at its Vancouver test hut on fiber-cement-clad walls found that assembly performance is governed largely by whatever drainage and drying path exists behind the cladding (BSC Research Report RR-1306, retrieved 2026-09-16). InspectAPedia's field-documented cases of gapping at butt joints and caulk failure on fiber-cement lap siding land on the same answer: clearance, joint caulking, and flashing are what decide whether an installation holds up over time (InspectAPedia field reports, retrieved 2026-09-16).
None of this singles out a particular manufacturer — it's just how the material class ages, and it explains why problems from a rushed install surface first on a shaded wall near a pond. That's part of why we lean toward LP SmartSide on Eagan's wetter lots, since engineered wood tends to forgive ordinary install variance more readily in this climate. When a fiber-cement job is what the owner or board picks anyway, our crews hold every gap, fastener spacing, flashing detail, and caulk joint to the exact numbers in the installation manual, since skipping any of them is what gets a warranty claim thrown out.
Is steel siding storm-proof?
Steel's storm-proof reputation outruns what the material actually delivers. It resists fire and rot and stays rigid, but a hailstone still leaves a mark on metal — adjusters routinely point to dinged gutters, downspouts, and fascia as their first clue a storm passed through. Choose steel for durability, low upkeep, and appearance, not on the assumption it makes a hail claim disappear.
Does your Eagan association have to approve the siding color?
Owning a unit inside one of Eagan's many townhome or association developments almost always means a color-approval step, and getting that started early keeps the schedule from slipping later. Our routine: bring actual siding samples that show the exact color and profile, photograph the building's current exterior in daylight, then draft submittal paperwork naming the product, color, and trim, shaped to fit whatever format the board needs.
Occasionally an older palette references something the manufacturer has since discontinued or reformulated. When that happens, we identify the closest match still in production among the lines we carry and flag it clearly as a substitution, rather than handing a board a swatch for something nobody can order anymore.
We can also scope this across an entire property. For a multi-building Eagan association, that means walking every building, dividing the work by building and elevation into workable phases, and pricing the whole thing as one combined project instead of several disconnected quotes — more on our multifamily and HOA experience and commercial siding capabilities.
- Physical color and profile samples held up against your building's existing siding on site
- Written documentation covering the product, color, and trim decisions, matched to your board's preferred format
- A current-production substitute researched and documented if the palette names something no longer made
- Multi-building scope divided into phases by building and elevation
- A single point of contact handling all communication with the board, property manager, and homeowners
Siding work from our crews
Do you do siding repairs in Eagan, or only full replacement?
Job size doesn't set a floor here. A cracked panel beneath a deck ledger, wind damage confined to one wall, or a section pulled open to reach flashing hidden behind old cedar — each is priced on its own, not folded into a whole-house replacement nobody requested.
The real limiting factor on repair work is matching color, and that surfaces fast on Eagan's shaded, wooded lots — pre-finished panels and vinyl age at different rates depending on how much sun they see, so a decades-old wall under tree cover frequently rejects a patch panel that would work fine on a sunnier wall. When a patch would visibly stand out, we'll tell you upfront and quote re-siding that elevation as the alternative, laying out the tradeoffs before you decide.
Whether the job is a repair or a full tear-off, any of these materials can be paired with insulated siding — we always bill it as a separate line item, keeping the added cost of that extra R-value clearly visible.
Who else does siding work in Eagan?
Most Eagan homeowners end up comparing bids from a mix of door-knock crews, yard-sign outfits, and whatever contractor a neighbor happened to recommend — with little practical way to vet any of those names. So we ran the check ourselves, against state licensing records, for the siding companies most frequently quoted alongside us across Eagan and the south metro.
This isn't about knocking anyone down. Everyone on this list holds the Minnesota residential building contractor license state law requires just to legally work on your home. We pass along what the license lookup turns up, mark anything we couldn't confirm, and let you draw your own conclusion.
| Company | MN license | Status | Expires | Licensed address | BBB |
|---|---|---|---|---|---|
| Craftsman's ChoiceCraftsmans Choice Inc | BC384780 | IssuedEnforcement flag on state record | 2027-03-31 | 5680 Quam Ave NE, Ste A, St Michael, MN 55376 | Unverified — BBB's published listing could not be retrieved on 2026-09-16. Check bbb.org directly. |
| Super SidersWinslow Companies (DBA Super Siders) | BC632296 | Issued | 2028-03-31 | 10533 Karston Ave NE, Albertville, MN 55301 | Unverified — BBB's published listing could not be retrieved on 2026-09-16. Check bbb.org directly. |
| Minnesota Exteriors IncMinnesota Exteriors Inc | BC002877 | Issued | 2028-03-31 | 8600 Jefferson Hwy, Maple Grove, MN 55369 | Unverified — BBB's published listing could not be retrieved on 2026-09-16. Check bbb.org directly. |
| Twin Cities Siding & RoofingTwin Cities Siding Professionals Operating Company LLC (DBA Twin Cities Siding and Roofing) | BC752041 | Issued | 2027-03-31 | 6500 Carlson Dr, Eden Prairie, MN 55346 | Unverified — BBB's published listing could not be retrieved on 2026-09-16. Check bbb.org directly. |
| TWS RemodelingThe Window Store Inc (DBA TWS Remodeling) | BC773859 | Issued | 2028-03-31 | 9000 Science Center Dr, New Hope, MN 55428 | Unverified — BBB's published listing could not be retrieved on 2026-09-16. Check bbb.org directly. |
| Garrett ConstructionGarrett Construction Limited Liability Company | BC785223 | Issued | 2027-03-31 | 2321 Rockwood Ave, St Paul, MN 55116 | Unverified — BBB's published listing could not be retrieved on 2026-09-16. Check bbb.org directly. |
| Anchor Roofing & ExteriorsHudson Enterprises Inc (DBA Anchor Roofing and Exteriors) | BC689351 | Issued | 2028-03-31 | 101 Bridgepoint Way, Ste 140, South St Paul, MN 55075 | Unverified — BBB's published listing could not be retrieved on 2026-09-16. Check bbb.org directly. |
- Craftsman's Choice — License BC384780 was listed as Issued through March 31, 2027, at 5680 Quam Ave NE, Ste A, St Michael, MN 55376 in the Minnesota DLI residential contractor export retrieved September 16, 2026. The export's enforcement-action field is marked, but the export provides no action type, date, outcome, case number, or order text; we therefore make no claim about what occurred. DLI's enforcement materials state, ‘A Consent Order is not a finding of fact or admission of guilt.’ The export does not establish whether this flag relates to a Consent Order. Verify the current license and any enforcement information directly at dli.mn.gov.
- Super Siders — Licensed and active with no enforcement flag on the export. Long-standing license, originally issued 2008. Their own marketing claims about years in business and families served are self-reported and we have not verified them.
- Minnesota Exteriors Inc — Licensed and active with no enforcement flag, and one of the oldest license records in the export — originally issued January 1992. A separate entity, Minnesota Exteriors Commercial LLC (BC741401), holds its own active license for commercial work.
- Twin Cities Siding & Roofing — Licensed and active with no enforcement flag. Note the operating entity name differs from the trade name — worth checking that the contract you are handed names the licensed entity.
- TWS Remodeling — Licensed and active with no enforcement flag. An earlier, similarly named license (BC283598, Window Store LLC The) shows as voluntarily terminated — the current active record is the one above.
- Garrett Construction — Licensed and active with no enforcement flag; the license number published on their own site matches the state record. The license was originally issued in August 2021, which is worth weighing against marketing that cites a longer operating history.
- Anchor Roofing & Exteriors — Licensed and active with no enforcement flag. As with several on this list, the licensed entity name differs from the trade name you see on the truck.
License numbers, status, expiry, and addresses below are taken from the Minnesota Department of Labor and Industry residential contractor license export, retrieved 2026-09-16. License status and enforcement flags change — confirm current status yourself at dli.mn.gov before you sign anything with anyone, including us. BBB accreditation and rating are shown as unverified because we could not retrieve BBB's own published listings at the time of writing; we would rather label that gap than repeat a number we have not read at the source.
Eagan siding questions
- How much does siding cost in Eagan, MN?
- Vinyl runs $900 to $950 per square (a square is 100 square feet), while LP SmartSide and fiber cement each land around $1,200 to $1,300 per square depending on finish. A typical Eagan split-entry or two-story with an attached two-car garage runs around 17 to 22 squares, which lands vinyl around $15,300 to $20,900 installed and either engineered wood or fiber cement around $20,400 to $28,600. The confirmed installed range for steel is $1,300 to $1,500 per square—around $13 to $15 per square foot—and the final price depends on the job.
- How long does a siding replacement take on an Eagan home?
- Most single-family jobs run three to five days on vinyl, LP SmartSide, or fiber cement, stretching to four or five days for steel. Wooded lots can add time when we're protecting trees and landscaping, or when rot shows up under old cedar or hardboard once we open the wall. In our experience, association approval usually adds more calendar time to a project than the actual install work does.
- What's the best siding option for converting off original cedar in Eagan?
- For most homeowners, LP SmartSide is the strongest fit. Its fastener-holding strength and thicker profile do a convincing job of mimicking cedar, and it withstands Minnesota's freeze-thaw swings and normal install variance better than a cement-based product. Vinyl, fiber cement, and steel are still options, and budget or appearance often decides between them.
- Does living next to a pond or wetland affect my siding?
- It can, mainly on north-facing walls. Homes near Eagan's ponds and wetlands tend to hold extra moisture on their shaded sides, which shows up early as algae and, given enough time, faster deterioration underneath the siding. Our inspections pay extra attention to those walls since they're usually the first to need work.
- Can you match siding to my existing brick?
- Yes. Plenty of Eagan homes built from the 1970s through the 1990s pair brick or stone on the front with siding wrapping the sides and back, and we work out the transition trim and flashing at those junctions before ordering material so the finished result looks planned rather than patched together.
- Is vinyl siding a good choice for an Eagan townhome?
- Often, yes. The .44-mil Exterior Portfolio Market Square panel we typically use never needs repainting and has enough flex to absorb everyday bumps, which makes it a solid, budget-friendly pick for a townhome end unit or association building whenever the approved palette allows vinyl.
- Is steel siding hail-proof?
- No. Steel won't burn or rot, and wooded Eagan lots make its woodpecker resistance a real bonus, but hail can still leave a dent. Insurance adjusters treat dinged-up gutters and fascia as proof a storm came through, so steel earns its keep as a low-maintenance choice — it just isn't a guaranteed win on a hail claim.
- Will my Eagan association need to approve my siding color?
- Almost certainly, if your property sits inside a townhome or association development — and Eagan has no shortage of those. We show up with physical samples of the color and profile, photograph your building's current exterior, and draft a submittal document your board can review and approve without back-and-forth. If the approved palette lists something discontinued, we'll pinpoint the nearest match still being made and flag it clearly as a substitution.
- Do you handle single-elevation siding repairs, or only full houses?
- Both, with no minimum job size. Whether it's a damaged section, one wall, or the whole exterior, each gets priced on its own terms. Color match is the real limiting factor, since sun and shade fade siding unevenly over time; when a patch wouldn't blend in, we'll say so and quote re-siding that elevation as the fix.
- Do you offer insulated siding in Eagan?
- Yes, but it's offered as an optional upgrade rather than folded into the standard price. Expect roughly $150 to $300 extra per square beyond the base material cost, and we bill it as its own separate line item every time, keeping that upgrade cost transparent.
- Can you help with a storm or insurance siding claim in Eagan?
- We do, though it's a smaller portion of what we handle in Eagan compared with standard replacement or cedar-to-engineered-wood conversions. When storm damage factors in, we photograph the impacted elevations and hand that documentation to your insurance adjuster; the work we do is the physical repair itself, not acting as your public adjuster.
Christian Musta
Owner, Midwest Building Exteriors
Christian Musta owns Midwest Building Exteriors, a family-led exterior restoration company with offices in Richfield, Eagan, and St. Croix Falls. He has spent 10 years in the insurance restoration industry and holds a Minnesota Public Adjuster license — a credential that reflects his command of policy language, coverage, and claim ethics. Midwest Building Exteriors does not act as a public adjuster on jobs it repairs; Christian applies that insurance knowledge to how our crews document damage and communicate with the homeowner's own insurance adjuster during a project. Every city guide on this site is written and reviewed by him, using measurements, adjuster scopes, and tear-off findings from jobs his own crews completed.
- 10 years of experience in the insurance restoration industry
- Licensed Minnesota Public Adjuster — held as a credential of competency, ethics, and policy-language knowledge, not an adjusting service we provide
- Minnesota-licensed residential building contractor
- Manufacturer-certified roofing installer (Owens Corning, TAMKO, CertainTeed)
- Installs vinyl, LP SmartSide, fiber cement, and steel siding systems
Last reviewed
Flexible financing options available.
We make protecting and upgrading your home or commercial property more affordable with flexible financing programs through trusted lending partners. Get started with comfortable monthly payments — ask us about financing options during your free inspection.
- Quick pre-qualification — no impact on your credit score
- 0% intro APR & low-rate plans through vetted partners
- Residential & commercial projects of every size